441661 442429 441663 442469 1401 Factor: fZ × 1.2 Factor: fZ × 1.6 Factor: fZ × 2.5 Factor: fZ × 1 Recommended cutting data for end mills HSSX-V2 TiALN-FUTURA 1 Mild,- case-hardened,- nitrided,- free machine,- heat treatable and ordinary tool steel up to 700 N/ mm2, GG < 200 HB Material group DIN 1.0037 1.0050 1.0060 1.0401 1.0402 1.0501 1.0503 1.0711 1.0718 1.0726 1.0727 1.0737 1.1141 1.1180 1.1191 1.1730 St 37-2 St 50-2 St 60-2 C 15 C 22 C 35 C 45 9 S 20 9 S MnPb 28 35 S 20 45 S 20 9 S MnPb 36 Ck 15 Ck 35 Ck 45 C 45 W, GG 15, 20, 25 Plexiglass, polyamide 4 For hard-cut material, high-temperature steel Ti- and Ni-alloys Material group DIN 1.4436 1.4980 2.4631 2.4632 3.7024 3.1764 X 5 CrNiMo 18 12 X 5 NiCrTi 26 15 NiCr 20 TiAl NiCr 20 C0 18 Ti Titanium-Titanium alloy Nimonic, Hastelloy, Monell Cutting data A Finishing – Application Standard Value Typ N Material group Cutting speed (m/min) TiALN-FUTURA dimension Feed per tooth (mm) 6 8 10 12 16 20 A 1 57-85 0.015 0.030 0.046 0.068 0.100 0.110 2 40-60 0.015 0.030 0.046 0.068 0.100 0.110 3 25-40 0.014 0.030 0.040 0.055 0.080 0.100 4 20-30 0.013 0.030 0.040 0.055 0.080 0.100 5 200-300 0.060 0.070 0.100 0.140 0.140 0.150 6 120-150 0.060 0.070 0.100 0.140 0.140 0.150 Cutting data B Roughing – Application Standard Value Typ HR Material group Cutting speed (m/min) TiALN-FUTURA dimension Feed per tooth (mm) 6 8 10 12 14 16 18 20 B 1 57-85 0.009 0.014 0.02 0.026 0.030 0.038 0.040 0.040 2 40-60 0.009 0.014 0.02 0.026 0.030 0.038 0.040 0.040 3 25-40 0.008 0.012 0.018 0.024 0.028 0.030 0.030 0.040 4 20-30 0.008 0.012 0.018 0.024 0.028 0.030 0.030 0.040 5 200-300 0.024 0.036 0.046 0.058 0.060 0.080 0.080 0.090 6 120-150 0.030 0.040 0.066 0.080 0.085 0.090 0.100 0.110 5 Cast aluminum, hardened aluminum e.g. G – AlSi 5Mg For table A For table B 6 Cast aluminum > 6% Si, copper/brass, copper alloys e.g. G – AlSi 10Mg CuNi 16 Si 2 Chemical resistant and high temperature steel. Alloyed steel up to 1000 N/mm2, heat treatable and tool steel, GG > 200 HB Material group DIN 1.1167 1.1221 1.2344 1.2363 1.2510 1.2542 1.2842 1.4006 1.4034 1.4057 1.4113 1.7131 1.7220 1.7225 1.7262 1.8159 1.8507 36 Mn 5 Ck 60 X 40 CrMo V 51 X 100 CrMo V 51 100 MnCrW 4 45 WCrV 7 90 MnCrV X 10 Cr 13 X 40 Cr 13 X 22 CrNi 17 X 6 CrMo 17 16 MnCr 5 34 CrMo 4 42 CrMo 4 15 CrMo 5 50 Cr V 4 34 CrAIMo 5 GG 30, 35, 40 3 Alloyed steel up to 1400 N/mm2, value and high-speed steel, chemical resistance steel Material group DIN 1.2080 1.2312 1.2316 1.2379 1.2436 1.2721 1.2767 1.3265 1.3343 1.3505 1.4306 1.4404 1.4541 1.4550 1.4571 1.6582 1.7147 1.7707 X 210 Cr 12 (RCC) 40 CrMn Mo 586 X 36 CrMo 17 X 155 Cr VMo 12 1 X 210 CrW 12 50 NiCr 13 X 45 NiCrMo 4 S 18 1-2-10 S 6-5-2 (DMo 5) 100 Cr 6 X 2 CrNi 18 9 X 2 CrNiMo 18 10 X 10 CrNiTi 18 9 (V4A) X 10 CrNiNb 18 9 X 6 CrNiMoTi 17 12 2 34 CrNiMo 6 20 MNCr 5 30 CrMo V 9 N N Factor: fZ x 1.2 0.1 d d d 1.5 d 0.5 d 0.25 d 1.5 d 1.5 d Factor: fZ x 1 Factor: fZ x 1.6 Factor: fZ x 2.5 Factor: fZ x 1.2 0.1 d d d 1.5 d 0.5 d 0.25 d 1.5 d 1.5 d Factor: fZ x 1 Factor: fZ x 1.6 Factor: fZ x 2.5 Factor: fZ x 1.2 0.1 d d d 1.5 d 0.5 d 0.25 d 1.5 d 1.5 d Factor: fZ x 1 Factor: fZ x 1.6 Factor: fZ x 2.5 Factor: fZ x 1.2 0.1 d d d 1.5 d 0.5 d 0.25 d 1.5 d 1.5 d Factor: fZ x 1 Factor: fZ x 1.6 Factor: fZ x 2.5 P P P S 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=