201010 201015 201130 201141 201020 201025 1434 mm 12-18 19-25 26-32 33-39 40-46 47-53 54-60 61-70 71-80 81-90 91-100 101-112 113-124 125-136 137-150 7/16 to 1-1/16" 3/4 to 1" 1-1/16 to 1-1/4" 1-5/16 to 1-9/16" 1-5/8 to 1-13/16" 1-7/8 to 2-1/16" 2-1/8 to 2-3/8" 2-13/32 to 2-3/4" 2-51/64 to 3-5/32" 3-3/16 to 3-9/16" 3-19/32 to 3-15/16" 3-31/32 to 4-13/32" 4-15/32 to 4-7/8" 4-15/16 to 5-11/32" 5-13/32 to 5-29/32" 1475 838 612 483 398 338 295 261 224 197 175 158 141 127 116 885 637 498 408 346 300 265 227 199 177 159 142 128 117 106 1327 754 550 434 358 304 265 234 201 177 157 142 127 114 104 796 537 448 367 311 270 230 204 179 159 143 128 115 105 95 930 590 430 335 280 239 205 182 155 137 122 108 98 89 80 620 450 340 285 240 210 185 160 140 125 110 100 90 81 75 795 500 370 290 240 200 175 155 135 117 104 94 84 76 69 530 380 300 245 265 180 160 135 120 105 95 85 77 70 63 660 420 305 240 195 165 145 125 110 95 85 75 68 63 57 440 320 250 200 170 150 130 115 100 90 80 70 65 58 50 530 340 245 195 160 135 115 103 87 77 68 62 55 56 45 350 250 200 165 140 120 105 90 78 70 63 56 51 46 42 2390 1510 1100 870 715 610 530 470 405 355 315 283 253 229 209 1590 1150 895 735 625 540 480 410 360 320 285 255 230 210 190 930 590 430 335 280 239 205 182 155 137 122 108 98 89 80 620 450 340 285 240 210 185 160 140 125 110 100 90 81 75 1325 840 615 490 400 340 295 260 225 195 174 157 140 127 116 885 635 500 410 345 300 265 230 200 175 160 145 130 117 105 930 590 430 335 280 239 205 182 155 137 122 108 98 89 80 620 450 340 285 240 210 185 160 140 125 110 100 90 81 75 800 670 490 386 318 271 236 200 180 150 140 120 105 99 91 700 510 398 327 277 240 212 182 159 142 127 110 100 95 85 508-511 512-515 516-519 520-523 528-529 530-531 POWER-MAX HEAVY-DUTY 10 POWER-MAX HEAVY-DUTY 20 POWER-MAX SUPER HEAVY-DUTY 30 POWER-MAX SUPER HEAVY-DUTY 55 EXTRA EASY-CUT EASY-CUT CONTACT INFORMATION For more information please call +1 330 928 7744 or send an email to ataorders@atatools.com SPEEDS (REV./MIN.) FOR CARBIDE-TIPPED HOLE SAWS Inch Steel < 500 N Stainless steel Aluminum Steel < 750 N Steel < 900 N Steel < 1200 N Steel < 1400 N Gray cast iron Brass Copper Plastics, Plexiglass, Fiberglass Use coolants see from page 1233 Notes on use: • Use rotation only. Switch off impact or hammer drill. • Avoid shock / impacts on the carbide tips. This leads to small carbide splinters which results to severe loss in performance • Do not tilt the hole saw in the hole • Remove the drill core after each operation. Do the same with chips and sawdust. 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=