291658 1521 8.0 × SL = 20 Material = Dispal 20 / 20% silicon rpm = 14,000 Vf = 2,000 ae = 0.5 mm ap = 10 mm 8.0 × SL = 20 Material = PA6 with 30% glass content rpm = 14,000 Vf = 2,500 ae = 4.0 mm ap = 4.0 mm 6 r 3.0 Material = FS2 ALU high-strength rpm = 14,000 Vf = 3,000 ae = 2.0 mm ap = 2.0 mm 8.0 × SL = 20 Material = CRP rpm = 14,000 Vf = 3,000 ae = 5.0 mm ap = 4.0 mm 8.0 × SL = 20 Material = CRP with Kevlar rpm = 14,000 Vf = 1,200 ae = 3.00 mm 8.0 × SL = 20 Material = Al Si 05 rpm = 14,000 Vf = 2,500 ae = 4.0 mm ap = 4.0 mm Dimension (mm) FEED RATE fz (mm per tooth) Material group WORKPIECE MATERIAL UNCOATED – Vc < 1 < 2 < 5 < 10 < 20 11.1 Polyamide 350 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyolefins 350 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyacetals 300 0.01 - 0.1 0.15 0.3 0.4 0.5 Polyester 300 0.01 - 0.1 0.15 0.3 0.4 0.5 Polycarbonate 300 0.01 - 0.1 0.15 0.3 0.4 0.5 Polyphenylenether 300 0.01 - 0.1 0.15 0.3 0.4 0.5 Aromat. polyamide 300 0.01 - 0.1 0.15 0.3 0.4 0.5 ABS 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Fluorpolymers 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polysulfone 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyphenylsulfon 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyethersulfon 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyetherimide 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyphenylsulfide 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyether ketone 400 - 500 0.01 - 0.05 0.1 0.2 0.35 0.45 Polyimide 80 - 100 0.005 - 0.03 0.05 0.1 0.2 0.35 CVD-End mill Art. 29 6526 CVD-End mill Art. 29 6526 CVD-End mill Art. 29 6522 CVD-End mill Art. 29 6526 CVD-End mill Art. 29 6526 CVD-End mill Art. 29 6526 Recommended cutting data for one-tooth end mills Test result: Very good test results with our CVD-end mills. 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=