201650 201650 201427 201428 201302 201650014 201650015 201650016 201650017 201650018 201650019 201650020 201650021 201650022 201650023 201650024 201650025 201650026 201650027 201650028 201650029 201650030 201650031 201650032 201650033 201650034 201650035 201650036 201650037 201650038 201650039 201650040 201650041 201650042 201650043 201650044 201650045 201650046 201650047 201650048 201650049 201650050 201650051 201650052 201650053 201650054 201650055 201650056 201650057 201650058 201650059 201650060 201650061 201650062 201650063 201650064 201650065 201650066 201650067 201650068 201650069 201650070 201650072 201650073 201650074 201650075 201650076 201650078 201650080 201650082 201650085 201650090 201650095 201650100 201650103 201650104 201650105 201650106 201650108 201650110 201650115 201650120 384 Weldon 14-60 mm Weldon 19 mm | 3/4" 61-120 mm Weldon 32 mm | 1.1/4" 80 mm | 3" E H I N H 1 2 7.98 × 130 mm 1 2 7.98 × 157 mm 1 2 6.34 × 130 mm Art. mm I 14 35/64" I 15 19/32" I 16 5/8" I 17 43/64" I 18 45/64" I 19 3/4" I 20 25/32" I 21 53/64" I 22 55/64" I 23 29/32" I 24 15/16" I 25 63/64" I 26 1.1/32" I 27 1.1/16" I 28 1.7/64" I 29 1.9/64" I 30 1.3/16" I 31 1.7/32" I 32 1.17/64" I 33 1.19/64" Art. mm I 34 1.11/32" I 35 1.3/8" I 36 1.27/64" I 37 1.29/64" I 38 1.1/2" I 39 1.17/32" I 40 1.37/64" I 41 1.39/64" I 42 1.21/32" I 43 1.11/16" I 44 1.47/64" I 45 1.49/64" I 46 1.13/16" I 47 1.27/32" I 48 1.57/64" I 49 1.59/64" I 50 1.31/32" I 51 2.1/64" I 52 2.3/64" I 53 2.3/32" Art. mm I 54 2.1/8" I 55 2.11/64" I 56 2.13/64" I 57 2.1/4" I 58 2.9/32" I 59 2.21/64" I 60 2.23/64" I 61 2.13/32" I 62 2.7/16" I 63 2.31/64" I 64 2.33/64" I 65 2.9/16" I 66 2.19/32" I 67 2.41/64" I 68 2.43/64" I 69 2.23/32" I 70 2.3/4" I 72 2.53/64" I 73 2.7/8" I 74 2.29/32" Art. mm I 75 2.61/64" I 76 2.63/64" I 78 3.5/64" I 80 3.5/32" I 82 3.15/64" I 85 3.11/32" I 90 3.35/64" I 95 3.47/64" I 100 3.15/16" I 103 4.1/16" I 104 4.3/32" I 105 4.9/64" I 106 4.11/64" I 108 4.1/4" I 110 4.21/64" I 115 4.17/32" I 120 4.23/32" 18-60 mm 61-120 mm I I 14-17 mm I 1563 ANNULAR CUTTERS CONTACT INFORMATION For more information please call +44 1530 261 145 or send an email to sales@atagarryson.com Carbide-tipped annular cutter, Weldon shank, drill depth 80 mm | 3" Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Steel Stainless Copper, brass, tin Plastics GRP/CRP Grey cast iron Hastelloy, Inconel, exotic materials APPLICATION EJECTOR PINS 1 + 2-PIECE APPLICATION EJECTOR PINS 2-PIECE Application: Insert piece 1 into the annular cutter shank. Push piece 2 onto part 1. Drill as deep as 50 mm cutting depth. Then remove piece 2 and continue drilling. 2 piece 2 piece 1 piece Packaging unit 2 pcs. Packaging unit 2 pcs. Packaging unit 2 pcs. ACCESSORIES Inch Inch Inch Inch Cutting data Movie Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on pages 536–537 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. One-piece ejector pins see next page < 1400 N > 900 N > 10% Si HARD-LINE 80 HARD-LINE 80 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=