201665 201665 201428 201124 201429 201399 201665018 201665019 201665020 201665021 201665022 201665023 201665024 201665025 201665026 201665027 201665028 201665029 201665030 201665031 201665032 201665033 201665034 201665035 201665036 201665037 201665038 201665039 201665040 201665041 201665042 201665043 201665044 201665045 201665046 201665047 201665048 201665049 201665050 201665051 201665052 201665053 201665054 201665055 201665056 201665057 201665058 201665059 201665060 388 18-54 mm Weldon 19 mm | 3/4" 55-60 mm Weldon 32 mm | 1.1/4" Weldon 150 mm | 5.29/32" E H I N H 1 2 152 7.98 × 205 mm 1 2 7.98 × 221.5 mm 1 2 1 7.98 × 205 mm 7.98 × 160 mm 2 7.98 × 160 mm Art. mm I 18 45/64" I 19 3/4" I 20 25/32" I 21 53/64" I 22 55/64" I 23 29/32" I 24 15/16" I 25 63/64" I 26 1.1/32" I 27 1.1/16" I 28 1.7/64" I 29 1.9/64" Art. mm I 30 1.3/16" I 31 1.7/32" I 32 1.17/64" I 33 1.19/64" I 34 1.11/32" I 35 1.3/8" I 36 1.27/64" I 37 1.29/64" I 38 1.1/2" I 39 1.17/32" I 40 1.37/64" I 41 1.39/64" Art. mm I 42 1.21/32" I 43 1.11/16" I 44 1.47/64" I 45 1.49/64" I 46 1.13/16" I 47 1.27/32" I 48 1.57/64" I 49 1.59/64" I 50 1.31/32" I 51 2.1/64" I 52 2.3/64" I 53 2.3/32" Art. mm I 54 2.1/8" I 55 2.11/64" I 56 2.13/64" I 57 2.1/4" I 58 2.9/32" I 59 2.21/64" I 60 2.23/64" 1563 20-54 mm I 55-60 mm I I 18-19 mm I 7.98 × 205 mm ANNULAR CUTTERS CONTACT INFORMATION For more information please call +44 1530 261 145 or send an email to sales@atagarryson.com Carbide-tipped annular cutter, Weldon shank, drill depth 150 mm | 5.29/32" Alu Steel Stainless Copper, brass, tin Plastics GRP/CRP Grey cast iron Hastelloy, Inconel, exotic materials APPLICATION APPLICATION EJECTOR PINS 1-PIECE 18-19mm APPLICATION EJECTOR PINS 2-PIECE Mount pin Art. 20 1429 into the cutter and drill up to 80mm cutting depth Take off the cutter and use pin Art. 20 1399 and continue drilling up to 150mm cutting depth. Application: Insert piece 1 into the annular cutter shank. Push piece 2 onto part 1. Drill as deep as 80 mm cutting depth. Then remove piece 2 and continue drilling up to cutting depth 150 mm. EJECTOR PINS 1 + 2-PIECE Packaging unit 2 pcs. Packaging unit 2 pcs. Packaging unit 2 pcs. 2 piece 2 piece 1 piece 1 piece Packaging unit 2 pcs. ACCESSORIES Cutting data Movie Inch Inch Inch Inch ATTENTION: The use of these 1+2-part ejector pins works only with extra long morse taper holders see Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 pages 536/537 < 1400 N > 900 N > 10% Si HARD-LINE 150 HARD-LINE 150 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=