201650N 201650N 201427 201302 201439 201650N014 201650N015 201650N016 201650N017 201650N018 201650N019 201650N020 201650N021 201650N022 201650N023 201650N024 201650N025 201650N026 201650N027 201650N028 201650N029 201650N030 201650N031 201650N032 201650N033 201650N034 201650N035 201650N036 201650N037 201650N038 201650N039 201650N040 201650N041 201650N042 201650N043 201650N044 201650N045 201650N046 201650N047 201650N048 201650N049 201650N050 456 I 1 2 7.98 × 130 mm 1 2 18-50 mm Nitto / Universal Nitto / Universal 19 mm 3/4" 80 mm | 3" E H I N H I I 14-17 mm 18-50 mm 6.34 × 130 mm 7.98 × 130 mm Art. mm I 14 35/64" I 15 19/32" I 16 5/8" I 17 43/64" I 18 45/64" I 19 3/4" I 20 25/32" I 21 53/64" I 22 55/64" I 23 29/32" Art. mm I 24 15/16" I 25 63/64" I 26 1.1/32" I 27 1.1/16" I 28 1.7/64" I 29 1.9/64" I 30 1.3/16" I 31 1.7/32" I 32 1.17/64" I 33 1.19/64" Art. mm I 34 1.11/32" I 35 1.3/8" I 36 1.27/64" I 37 1.29/64" I 38 1.1/2" I 39 1.17/32" I 40 1.37/64" I 41 1.39/64" I 42 1.21/32" I 43 1.11/16" Art. mm I 44 1.47/64" I 45 1.49/64" I 46 1.13/16" I 47 1.27/32" I 48 1.57/64" I 49 1.59/64" I 50 1.31/32" 1563 ANNULAR CUTTERS CONTACT INFORMATION For more information please call +44 1530 261 145 or send an email to sales@atagarryson.com It is possible to use this one-piece ejector pin in combination with tool holder article 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (see pages 536–537). You can drill as deep as 110 mm in one working process without changing. Robust and easy. EJECTOR PINS 2-PIECE APPLICATION EJECTOR PINS 2-PIECE Application: Insert piece 1 into the annular cutter shank. Push piece 2 onto part 1. Drill as deep as 50 mm cutting depth. Then remove piece 2 and continue drilling. 2 piece Carbide-tipped annular cutter, Nitto/Universal shank, drill depth 80 mm | 3" Larger up to 60mm with adaptor see Art. 20 1650 page 384 ∙ Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Steel Stainless Copper, brass, tin Plastics GRP/CRP Grey cast iron Hastelloy, Inconel, exotic materials APPLICATION EJECTOR PINS 1 piece 1 piece Packaging unit 2 pcs. Packaging unit 2 pcs. Packaging unit 2 pcs. ACCESSORIES Inch Inch Inch Inch Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on pages 536–537 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. Cutting data Movie < 1400 N > 900 N > 10% Si HARD-LINE 80 HARD-LINE 80 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=