201660N 201660N 201428 201304 201399 201660N014 201660N015 201660N016 201660N017 201660N018 201660N019 201660N020 201660N021 201660N022 201660N023 201660N024 201660N025 201660N026 201660N027 201660N028 201660N029 201660N030 201660N031 201660N032 201660N033 201660N034 201660N035 201660N036 201660N037 201660N038 201660N039 201660N040 201660N041 201660N042 201660N043 201660N044 201660N045 201660N046 201660N047 201660N048 201660N049 201660N050 458 I 1 2 18-50 mm I I 14-17 mm 18-50 mm Nitto / Universal Nitto / Universal 19 mm 3/4" 110 mm | 4" 7.98 × 160 mm E H I N H 6.34 × 160 mm 7.98 × 157 mm 1 2 Art. mm 2 1 6 01 I 14 35/64" 2 1 6 01 I 15 19/32" 2 1 6 01 I 16 5/8" 2 1 6 01 I 17 43/64" 2 1 6 01 I 18 45/64" 2 1 6 01 I 19 3/4" 2 1 6 02 I 20 25/32" 2 1 6 02 I 21 53/64" 2 1 6 02 I 22 55/64" 2 1 6 02 I 23 29/32" Art. mm 2 1 6 02 I 24 15/16" 2 1 6 02 I 25 63/64" 2 1 6 02 I 26 1.1/32" 2 1 6 02 I 27 1.1/16" 2 1 6 02 I 28 1.7/64" 2 1 6 02 I 29 1.9/64" 2 1 6 03 I 30 1.3/16" 2 1 6 03 I 31 1.7/32" 2 1 6 03 I 32 1.17/64" 2 1 6 03 I 33 1.19/64" Art. mm 2 1 6 03 I 34 1.11/32" 2 1 6 03 I 35 1.3/8" 2 1 6 03 I 36 1.27/64" 2 1 6 03 I 37 1.29/64" 2 1 6 03 I 38 1.1/2" 2 1 6 03 I 39 1.17/32" 2 1 6 04 I 40 1.37/64" 2 1 6 04 I 41 1.39/64" 2 1 6 04 I 42 1.21/32" 2 1 6 04 I 43 1.11/16" Art. mm 2 1 6 04 I 44 1.47/64" 2 1 6 04 I 45 1.49/64" 2 1 6 04 I 46 1.13/16" 2 1 6 04 I 47 1.27/32" 2 1 6 04 I 48 1.57/64" 2 1 6 04 I 49 1.59/64" 2 1 6 05 I 50 1.31/32" 1563 ANNULAR CUTTERS CONTACT INFORMATION For more information please call +44 1530 261 145 or send an email to sales@atagarryson.com It is possible to use this one-piece ejector pin in combination with tool holder article 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (see pages 536–537). You can drill as deep as 110 mm in one working process without changing. Robust and easy. EJECTOR PINS 2-PIECE APPLICATION EJECTOR PINS 2-PIECE Application: Insert piece 1 into the annular cutter shank. Push piece 2 onto part 1. Drill as deep as 50 mm cutting depth. Then remove piece 2 and continue drilling. EJECTOR PINS 1 piece Carbide-tipped annular cutter, Nitto/Universal shank, drill depth 110 mm | 4" Larger up to 55mm with adaptor possible. See Art. 20 1660 page 386 ∙ Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Steel Stainless Copper, brass, tin Plastics GRP/CRP Grey cast iron Hastelloy, Inconel, exotic materials APPLICATION 1 piece 2 piece Packaging unit 2 pcs. Packaging unit 2 pcs. Packaging unit 2 pcs. ACCESSORIES Inch Inch Inch Inch Cutting data Movie Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on pages 536–537 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. < 1400 N > 900 N > 10% Si HARD-LINE 110 HARD-LINE 110 11 Index 10 9 OIL 8 7 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=